ODROID-X bringup log

買了條HDMI female-to-DVI male轉接頭和HDMI A-to-D傳輸線，並拿了個5V4A的變壓器改頭

插上電源後D4亮起來了，但因為還沒有放SD卡，按下power後馬上就會關機
CON3上的VDD-IO也只有在按下power時才有1.8V output, 放開就沒有了

OP-1010取掉R7，在VO33與VD232上焊上排針
把CON3上的pin, 從靠CON3字樣起算分別是VDD-IO, TTA-RXD, TTA-TXD, 接地

• VDD-IO 接到 VD232
• TTA-RXD接到Rx
• TTA-TXD接到Tx
• 接地 接到 Gnd

弄一塊8G以上的SD卡，按照以下程序安裝:
SD Card setup for ODROID-X
http://com.odroid.com/sigong/blog/blog_list.php?bid=130

解出來的*.odt不要放在桌面，可能是Win32DiskImager不支援長檔名或中文路徑

How to turn on your ODROID-X.
 http://odroid.foros-phpbb.com/t1172-how-to-turn-on-your-odroid-x
插上SD卡按了power以後，如果boot到u-boot，D5和D6會半亮
進kernel後，D5會全亮，D6會每秒閃一次

(原來我以為UART應該odroid Rx接op-1010 Tx,但是反而會讓odroid boot不起來，D5D6都半亮，似乎卡在u-boot)

OP-1010看的到輸出，但是HDMI仍然沒有輸出
Console Output

[   48.370127] No such irq type 0
[   48.370252] setting trigger mode 0 for irq 383 failed (exynos_irq_eint_set_type+0x0/0x218)
[   51.931581] No such irq type 0
[   51.931705] setting trigger mode 0 for irq 383 failed (exynos_irq_eint_set_type+0x0/0x218)
[   81.173680] No such irq type 0
[   81.173806] setting trigger mode 0 for irq 383 failed (exynos_irq_eint_set_type+0x0/0x218)

HDMI - hdmi output
http://odroid.foros-phpbb.com/t1419-hdmi-output?highlight=HDMI
HDMI - odroid-X with DVI LCD?
http://odroid.foros-phpbb.com/t1193-odroid-x-with-dvi-lcd?highlight=HDMI
FAQs - ODROID :: Hardkernel
http://www.hardkernel.com/renewal_2011/products/prdt_info.php?g_code=G133999328931&tab_idx=3

DISPLAY
What display can I use?
There are HDMI out and RGB digital out are available on ODROID-X.
HDMI can support only 720p/1080p resolution with 16:9 wide display.
HDMI-DVI converter will not work properly because Exynos4 HDMI is not compatible with VESA standard.
So most of old PC monitors can't be used.

We recommend LCD kit if your monitor/TV is old model. LCD kit contains LCD panel + interface board + LVDS cable + power supply.

幹...中招了...

TV: Sharp LC-32A33T 1080p顯示不相容，720p可以用
Monitor: Acer P235H 1080p/720p皆可

這下該怎麼辦呢.....我不想再促進經濟了呀...

新灌的SD卡的data partition都沒有format，在Android裡會顯示損壞，選擇重新format就好了